PIE 525 Plus Thermocouple & Milliamp Calibrator
Actualizado: 2024-01-18
The PIE 525 Plus Thermocouple & Milliamp Calibrator 3-in-1 thermocouple, RTD, and full function milliamp calibrator. The 525 Plus includes a full function diagnostic milliamp calibrator that sources and reads 0.000 to 24.000 mA, simulates two wire transmitters, powers & measures transmitters with its internal 24V supply, has a built-in 250 ohm resistor for HART compatibility and PIE\'s patented Ground Leak Detection. Competitive calibrators allow you to calibrate temperature transmitters but don\'t have the ability to test other instruments in a 4 to 20 mA loop. The two parts of the calibrator sources and reads both 14 thermocouples types and 12 RTD types to 0.001°F & °C.
Extech PRC20 Thermocouple Calibrator
Actualizado: 2024-01-18
The Extech PRC20 Thermocouple Calibrator provides a high accuracy calibration function that simulates precision thermocouple outputsfor use in calibrating thermometers, transmitters, controllers or recorders. The palm sized unit has double molded housing with a large
dot-matrix digital backlit LCD with thermocouple type indication.
Time Electronics 7000 Temperature Calibrator
Actualizado: 2024-01-18
The Time Electronics 7000 temperature calibrator is a portable process control instrument that combines a precision digital thermometer (using RTD probes) with an RTD/ohms calibrator. Compact and easy to use, the 7000 solves the problem of making high accuracy temperature measurements without using bulky mains powered instrumentation. Powered from internal long life rechargeable batteries or an external mains adaptor, it is equally valuable in laboratory, workshop or the field. It can also be used as an external temperature reference for dry block and other precision temperature baths.
Isotech Model 983 Hot Plate Surface Sensor Calibrator
Actualizado: 2024-01-18
With a temperature range of 35 to 350°C and stabilization time of just 10 minutes, the Isotech Model 938 small hot plate offers a lightweight, portable calibration system designed for surface mounted sensors. The temperature range is set using an advanced, yet easy-to-use, temperature controller which features 0.001 resolution below 100°C (0.1° above 100°C). Depending on sensors and method of use, the typical uncertainty is 1°C. For higher accuracy, a calibrated surface sensor can be placed alongside the sensor under test.
Isotech Model 944 Surface Measurement System
Actualizado: 2024-01-18
Using a fine wire type N thermocouple as the surface temperature sensor, the Isotech Model 944 pairs that with a second junction 2 to 3mm along the thermocouple and senses the temperature difference due to heat flux along the sensor. A heater heats the thermocouple stem until the temperature gradient is zero, thus creating a measurement without stem conduction or disturbance of the hot plate\'s surface.
PIE 322 Thermocouple Calibrator
Actualizado: 2024-01-17
The Practical Instruments Electronics (PIE) PIECAL 322 automated thermocouple calibrator is easy to use and very versatile. Just plug in any thermocouple via a miniature thermocouple jack to calibrate and measure all your thermocouple instruments and thermocouple sensors. The PIECAL 322 works with any thermocouple including types J, K, T and E.
Fluke 724 Temperature Calibrator
Actualizado: 2024-01-17
The Fluke 724 temperature calibrator is one tool that is able to test all temperature sensors and transmitters in yourplant. The Fluke 724 can measure and source 12 thermocouples types and seven RTD types, plus volts and ohms. The 724
even handles high-speed pulsed RTD circuits and provides loop power.
PIE 211 Automated RTD Calibrator
Actualizado: 2024-01-17
The Practical Instrument Electronics (PIE) 211 automated RTD calibrator can be used to check and calibrate all RTD instruments and measure RTD sensors with automatic indication of connections on the display for simple hookups. The PIE 211 comes with a rubber boot and a rugged, low-profile switch for protection and its backlit display makes it easy to use in poorly lit areas.
Additel ADT850 Laboratory Thermocouple Calibration Furnace
Actualizado: 2024-01-17
The Additel ADT850 laboratory thermocouple calibration furnace provides calibration and annealing support for a wide variety of thermocouple types and lengths.The selectable \"mode of operation\" integrated into the touchscreen interface allows users to select from nine different modes, accounting for immersion depths from
200 to 370 mm. The user also has the ability to select a variety of insert types to accommodate reliable and repeatable measurements for both metal and ceramic style probes.
PIE 422 / 422Plus Thermocouple Calibrator
Actualizado: 2024-01-17
The PIE 422 / 422Plus thermocouple calibrator measures and calibrates thermocouple instruments and sensors, including types J, K, T, E, R, S, B, N, G, C, D, L (J-DIN), U (T-DIN) and P (Platinel II). It is available as s single channel thermocouple (PIE 422) or double channel milliamp and thermocouple calibrator (PIE 422Plus).
