Mostrando los 5 resultados

Series CMT Carbon Monoxide Transmitter

Código: Series CMT Carbon Monoxide Transmitter
Valorado con 0 de 5

Actualizado: 2024-01-04

The Series CMT Carbon Monoxide Transmitter accurately detects and transmits low concentrations of carbon monoxide inside a parking garage or loading dock. Transmitters can be ordered in wall mount or duct mount configurations. Universal current and voltage outputs are field selectable and match most common building management controllers. Optional relays and alarm buzzer are available on the wall mount models to directly connect to a warning light or exhaust fan. The Series CMT can be field calibrated using internal potentiometers. Software settings such as set points for optional relay outputs are password protected.

Series GSTA Carbon Monoxide/Nitrogen Dioxide Gas Transmitter

Código: Series GSTA Carbon Monoxide/Nitrogen Dioxide Gas Transmitter
Valorado con 0 de 5

Actualizado: 2024-01-04

The Series GSTA Carbon Monoxide/Nitrogen Dioxide Transmitters
monitor the gas concentration in underground parking garages and loading docks.
Carbon monoxide is commonly used to measure the exhaust of gasoline engines,
while nitrogen dioxide is used for diesel engines. Field selectable current and
voltage outputs allow the transmitter to be used with almost any building
management controller. For carbon monoxide units, the user can select the output
range to be from 0 to 50 PPM or up to 0 to 500 PPM. Nitrogen dioxide units come with a
standard 0 to 10 PPM range. The output can be inverted to read 20 to 4 mA or 10
(5) to 0 VDC using internal dip switches.

Series CMT200 Carbon Monoxide Transmitter

Código: Series CMT200 Carbon Monoxide Transmitter
Valorado con 0 de 5

Actualizado: 2024-01-04

The Series CMT200 Carbon Monoxide Transmitter provides a field selectable
current or voltage output that is proportional to the gas concentration in underground
parking garages, vehicle maintenance facilities, or mechanical rooms. A field replaceable,
electrochemical sensor provides accurate readings for up to 4 years with proper calibration.
Field calibration can be done by using Model GCK-200CO-2000CO2 calibration gas, Model
A-507A calibration adapter, and the on board span and zero potentiometers.

Series GSTC Carbon Monoxide/Nitrogen Dioxide Gas Transmitter

Código: Series GSTC Carbon Monoxide/Nitrogen Dioxide Gas Transmitter
Valorado con 0 de 5

Actualizado: 2024-01-04

The Series GSTC Carbon Monoxide/Nitrogen Dioxide Gas
Transmitter monitors the gas concentration in underground parking garages and
loading docks. The carbon monoxide transmitter is used to measure the exhaust of
gasoline engines, while the nitrogen dioxide transmitter is used for diesel engines. The
Series GSTC is compatible with either BACnet or Modbus® communication protocol,
allowing the transmitter to be used with almost any building management controller.
The GSTC output is communicated over an RS-485 wire via BACnet or Modbus®
communication protocol. To maximize the accuracy of the Series GSTC, the sensor
can be field-calibrated using the A-449 remote LCD display. When the sensor reaches
the end of its life, the display will indicate that the sensor needs to be replaced.
BACnet and Modbus® communication protocol recommend limiting the number of
nodes in any segment to 32. Therefore, the transceiver may be rated at one unit load.
Fractional loads are also acceptable. The Series GSTC accounts as an eighth of a
load on the MS/TP network.

Model CMS300 Carbon Monoxide Transmitter and Switch

Código: Model CMS300 Carbon Monoxide Transmitter and Switch
Valorado con 0 de 5

Actualizado: 2024-01-04

The Model CMS300 Carbon Monoxide Transmitter and Switch provides a field
selectable current or voltage output that is proportional to the carbon monoxide
concentration in underground parking garages, vehicle maintenance facilities, or
mechanical rooms. An integral relay can be used for alarm conditions and is configured
with preset jumper selectable ranges of 25, 60, or 150 PPM. Field calibration can be
done by using Model GCK-200CO-2000CO2 calibration gas, Model A-507 calibration
adapter, and the on board zero and span potentiometers.