ER Fixed Flush Element Probe 2700/27005
Actualizado: 2024-01-03
Model 2700 and 27005 fixed process probes have a flat strip measuring element sealed and mounted at the end of a heavy walled stainless steel tube. The measuring element can be positioned flush with the inner surface of the pipe or vessel. Corrosion or erosion can then be measured right at this surface, and the lines may be pigged without moving the probes.Dual Sensor Electrical Resistance (ER) Temperature Probes
Actualizado: 2024-01-03
Temperature is one of the most important controllable factors affecting corrosion rate, particularly in refineries, chemical, and petrochemical process plants. A rule of thumb is that corrosion rates double for each 10 degrees C temperature rise. The ability to track temperature and corrosion rates simultaneously is a powerful tool in the corrosion management of such plants.CUI Corrosion Fuse Wire Sensor
Actualizado: 2024-01-01
The Insulated Braid Wire Sensor (patent pending) is designed to detect corrosion that has occurred over a relatively large area. A single insulated carbon steel wire of a certain element thickness, or multiple wires of varying thickness, eg 5 mil, 10 mil, 15 mil, and 20 mil thick wires, may be installed.CUI Electrical Resistance Probe Sensor
Actualizado: 2024-01-01
The CUI Electrical Resistance (ER) probe sensor is an individual electrical resistance (ER) probe that provides a measurement of the corrosion rate near the pipe surface. It is useful in determining the underlying cause of corrosion and the ability to measure changes in corrosion conditions, ie the effectiveness of repairs, temperature cycles or environmental changes eg after a severe rain storm.High Pressure Linear Polarization Resistance (LPR) Probe 6080
Actualizado: 2024-01-01
This probe employs two identical electrodes which are mounted at the end of the probe by threaded, insulated, glass-sealed studs. The glass seals provide high pressure integrity. The probe is sealed into the hollow plug of the access fitting with a ceramic filled teflon seal.Hydrogen Probes 6400
Actualizado: 2024-01-01
Cosasco hydrogen probes detect hydrogen gas by the simple hydrogen pressure increase produced in an artificial cavity in the steel, i.e. the same mechanism as hydrogen blistering. The pressure build-up is directly proportional to the flux of atomic hydrogen, which can be determined by implementation of the ideal gas law. If the volume of the hydrogen probe cavity and the cross-sectional area across which diffusion is occurring is known, determination of the flux is a simple calculation.LPR Probe 70012/70022
Actualizado: 2024-01-01
The Model 70012/70022 LPR Probe provides a more rugged construction and is ideal for plant use in a bypass rack where removal under pressure is not required. This LPR probe employs two replaceable, identical electrodes which are mounted at the end of the probe by threaded, insulated studs.Linear Polarization Resistance (LPR) Corrosion Monitoring By-Pass Rack
Actualizado: 2024-01-01
Corrosion Monitoring LPR By-Pass Racks are commonly used in industrial water treatment systems to determine the corrosive properties of potable - process - or cooling water. The By-Pass Rack creates a side stream off the main system in which corrosion test coupons can be exposed to system water under controlled and reproducible conditions. The corrosion coupons can be periodically removed and either visually examined or returned to the laboratory for determination of weight loss, corrosion rate, and pitting severity.Linear Polarization Resistance (LPR) Probe Accessories
Actualizado: 2024-01-01
LPR and Temperature LPR probes are designed for safe installation and operation in various environments. Where danger of blowout exists, use of an appropriate safety device should be considered mandatory. This equipment is designed and tested for reliability, using established principles of operation.Retractable Electrical Resistance (ER) Probe 3500/3500HT
Actualizado: 2024-01-01
Model 3500 Probes provide a large test surface, excellent dynamic temperature response and protection of reference element.They are ideally suited to the more aggressive plant conditions and may be used in very aggressive organic or inorganic fluids over the entire pH range 0-14, subject to process containment requirements.Retractable Flush Electrical Resistance (ER) Probe 3700/37005
Actualizado: 2024-01-01
Model 3700 and 37005 retractable process probes have a flat strip measuring element sealed and mounted at the end of a heavy walled stainless steel tube. By adjusting the position of the probe or proper selection of the physical dimensions of the coupling system, the measuring element can be positioned flush with the inner surface of the pipe or vessel.Retractable Linear Polarization Resistance (LPR) Probe 80012/80022
Actualizado: 2024-01-01
These Models are ideal for direct mounting into plant pipework or vessels and allow insertion or removal while under system pressure. The electrode seals are suitable for all pH ranges. These probes employ two replaceable, identical electrodes which are mounted at the end of the probe by threaded, insulated studs. Two electrode probes are suitable for the majority of problems where LPR techniques are applicable. When monitored by “Solution Resistance Compensating” instruments such as the LPR RDC, Aquamate®, or Model 90030 they may be used in low conductivity solutions (see Fig. 1 of the LPR Probe Selection Guide). LPR Probes are used by major companies world-wide to measure corrosion in waterfloods, cooling water loops and other aqueous systems and to provide control of inhibitor addition for optimum economy and corrosion protection.?Retractable Small Diameter Electrical Resistance (ER) Probe 35004/35004HT
Actualizado: 2024-01-01
Model 35004 Retractable Process Probes are ideally suited to the more aggressive plant conditions and may be used in very aggressive organic or inorganic fluids over the entire pH range 0-14, subject to process containment requirements. These probes are standard in mild steel, 3004 S.S. and 316 S.S..